esp8266/doc/reference.rst

Reference
=========

Digital IO
----------

Pin numbers in Arduino correspond directly to the ESP8266 GPIO pin
numbers. ``pinMode``, ``digitalRead``, and ``digitalWrite`` functions
work as usual, so to read GPIO2, call ``digitalRead(2)``.

Digital pins 0—15 can be ``INPUT``, ``OUTPUT``, or ``INPUT_PULLUP``. Pin
16 can be ``INPUT``, ``OUTPUT`` or ``INPUT_PULLDOWN_16``. At startup,
pins are configured as ``INPUT``.

Pins may also serve other functions, like Serial, I2C, SPI. These
functions are normally activated by the corresponding library. The
diagram below shows pin mapping for the popular ESP-12 module.

.. figure:: esp12.png
   :alt: Pin Functions

   Pin Functions

Digital pins 6—11 are not shown on this diagram because they are used to
connect flash memory chip on most modules. Trying to use these pins as
IOs will likely cause the program to crash.

Note that some boards and modules (ESP-12ED, NodeMCU 1.0) also break out
pins 9 and 11. These may be used as IO if flash chip works in DIO mode
(as opposed to QIO, which is the default one).

Pin interrupts are supported through ``attachInterrupt``,
``detachInterrupt`` functions. Interrupts may be attached to any GPIO
pin, except GPIO16. Standard Arduino interrupt types are supported:
``CHANGE``, ``RISING``, ``FALLING``.

Analog input
------------

ESP8266 has a single ADC channel available to users. It may be used
either to read voltage at ADC pin, or to read module supply voltage
(VCC).

To read external voltage applied to ADC pin, use ``analogRead(A0)``.
Input voltage range is 0 — 1.0V.

To read VCC voltage, use ``ESP.getVcc()`` and ADC pin must be kept
unconnected. Additionally, the following line has to be added to the
sketch:

.. code:: cpp

    ADC_MODE(ADC_VCC);

This line has to appear outside of any functions, for instance right
after the ``#include`` lines of your sketch.

Analog output
-------------

``analogWrite(pin, value)`` enables software PWM on the given pin. PWM
may be used on pins 0 to 16. Call ``analogWrite(pin, 0)`` to disable PWM
on the pin. ``value`` may be in range from 0 to ``PWMRANGE``, which is
equal to 1023 by default. PWM range may be changed by calling
``analogWriteRange(new_range)``.

PWM frequency is 1kHz by default. Call
``analogWriteFreq(new_frequency)`` to change the frequency.

Timing and delays
-----------------

``millis()`` and ``micros()`` return the number of milliseconds and
microseconds elapsed after reset, respectively.

``delay(ms)`` pauses the sketch for a given number of milliseconds and
allows WiFi and TCP/IP tasks to run. ``delayMicroseconds(us)`` pauses
for a given number of microseconds.

Remember that there is a lot of code that needs to run on the chip
besides the sketch when WiFi is connected. WiFi and TCP/IP libraries get
a chance to handle any pending events each time the ``loop()`` function
completes, OR when ``delay`` is called. If you have a loop somewhere in
your sketch that takes a lot of time (>50ms) without calling ``delay``,
you might consider adding a call to ``delay`` function to keep the WiFi
stack running smoothly.

There is also a ``yield()`` function which is equivalent to
``delay(0)``. The ``delayMicroseconds`` function, on the other hand,
does not yield to other tasks, so using it for delays more than 20
milliseconds is not recommended.

Serial
------

``Serial`` object works much the same way as on a regular Arduino. Apart
from hardware FIFO (128 bytes for TX and RX) ``Serial`` has
additional 256-byte TX and RX buffers. Both transmit and receive is
interrupt-driven. Write and read functions only block the sketch
execution when the respective FIFO/buffers are full/empty. Note that
the length of additional 256-bit buffer can be customized.

``Serial`` uses UART0, which is mapped to pins GPIO1 (TX) and GPIO3
(RX). Serial may be remapped to GPIO15 (TX) and GPIO13 (RX) by calling
``Serial.swap()`` after ``Serial.begin``. Calling ``swap`` again maps
UART0 back to GPIO1 and GPIO3.

``Serial1`` uses UART1, TX pin is GPIO2. UART1 can not be used to
receive data because normally it's RX pin is occupied for flash chip
connection. To use ``Serial1``, call ``Serial1.begin(baudrate)``.

If ``Serial1`` is not used and ``Serial`` is not swapped - TX for UART0
can be mapped to GPIO2 instead by calling ``Serial.set_tx(2)`` after
``Serial.begin`` or directly with
``Serial.begin(baud, config, mode, 2)``.

By default the diagnostic output from WiFi libraries is disabled when
you call ``Serial.begin``. To enable debug output again, call
``Serial.setDebugOutput(true)``. To redirect debug output to ``Serial1``
instead, call ``Serial1.setDebugOutput(true)``.

You also need to use ``Serial.setDebugOutput(true)`` to enable output
from ``printf()`` function.

The method ``Serial.setRxBufferSize(size_t size)`` allows to define the
receiving buffer depth. The default value is 256.

Both ``Serial`` and ``Serial1`` objects support 5, 6, 7, 8 data bits,
odd (O), even (E), and no (N) parity, and 1 or 2 stop bits. To set the
desired mode, call ``Serial.begin(baudrate, SERIAL_8N1)``,
``Serial.begin(baudrate, SERIAL_6E2)``, etc.

A new method has been implemented on both ``Serial`` and ``Serial1`` to
get current baud rate setting. To get the current baud rate, call
``Serial.baudRate()``, ``Serial1.baudRate()``. Return a ``int`` of
current speed. For example

.. code:: cpp

    // Set Baud rate to 57600
    Serial.begin(57600);

    // Get current baud rate
    int br = Serial.baudRate();

    // Will print "Serial is 57600 bps"
    Serial.printf("Serial is %d bps", br);

| ``Serial`` and ``Serial1`` objects are both instances of the
  ``HardwareSerial`` class.
| I've done this also for official ESP8266 `Software
  Serial <https://github.com/esp8266/Arduino/blob/master/doc/libraries.md#softwareserial>`__
  library, see this `pull
  request <https://github.com/plerup/espsoftwareserial/pull/22>`__.
| Note that this implementation is **only for ESP8266 based boards**,
  and will not works with other Arduino boards.

Progmem
-------

The Program memory features work much the same way as on a regular
Arduino; placing read only data and strings in read only memory and
freeing heap for your application. The important difference is that on
the ESP8266 the literal strings are not pooled. This means that the same
literal string defined inside a ``F("")`` and/or ``PSTR("")`` will take
up space for each instance in the code. So you will need to manage the
duplicate strings yourself.

There is one additional helper macro to make it easier to pass
``const PROGMEM`` strings to methods that take a ``__FlashStringHelper``
called ``FPSTR()``. The use of this will help make it easier to pool
strings. Not pooling strings...

.. code:: cpp

    String response1;
    response1 += F("http:");
    ...
    String response2;
    response2 += F("http:");

using FPSTR would become...

.. code:: cpp

    const char HTTP[] PROGMEM = "http:";
    ...
    {
        String response1;
        response1 += FPSTR(HTTP);
        ...
        String response2;
        response2 += FPSTR(HTTP);
    }