Remove test sketches

test/LoRaDumpRegisters/LoRaDumpRegisters.ino

@@ -1,26 +0,0 @@
-/*
-  LoRa register dump
-  context: Arduino
-
-*/
-#include <SPI.h>              // include libraries
-#include <LoRa.h>
-
-void setup() {
-  while (!Serial);
-  Serial.begin(9600);               // initialize serial
-  Serial.println("LoRa Receiver");
-  LoRa.setPins(7, 6, 1);            // set CS, reset, IRQ pin
-  if (!LoRa.begin(915E6)) {         // initialize ratio at 915Mhz
-    Serial.println("LoRa init failed. Check your connections.");
-    while (true);                   // if failed, do nothing
-  }
-  LoRa.sleep();
- LoRa.dumpRegisters(Serial);
-}
-
-
-void loop() {
-  
-}
-

test/LoRaDuplexAutoContinuous/LoRaDuplexAutoContinuous.ino

@@ -1,129 +0,0 @@
-/*
-  LoRa Duplex communication with callback 
-  context: Arduino
-
-  This sketch is for testing transmission between two devices, one an Uno,
-  and one not an Uno (a MKRZero, in my case). The #defines are there for that
-  reason,and should be removed before making this a real example.
-
-   It sends every half second, and polls continually for new packets.
-
-   There's a block that's commented out in the loop that lets you change the
-   sync word on one device, to test sync address filtering.  The SyncWordTest.xslx
-   spreadsheet shows some typical results.
-*/
-#include <SPI.h>              // include libraries
-#include <LoRa.h>
-
-#if defined (__AVR_ATmega328P__)
-#define irqPin 2
-#define addr 0xFD
-#define netId 0x18
-#define change 1
-#else
-#define irqPin 1
-#define addr 0xFE
-#define netId 0x18
-#define change 0
-#endif
-
-String message;               // outgoing message
-byte messageId = 0;           // ID of outgoing message
-byte localAddress = addr;     // address of this device
-byte destination = 0xFF;      // destination to send to
-byte syncWord = netId;         // Sync word (network ID)
-long lastSend = 0;
-
-void setup() {
-  while (!Serial);
-  Serial.begin(9600);               // initialize serial
-  Serial.println("LoRa Receiver");
-  LoRa.setPins(7, 6, irqPin);            // set CS, reset, IRQ pin
-  if (!LoRa.begin(915E6)) {         // initialize ratio at 915Mhz
-    Serial.println("LoRa init failed. Check your connections.");
-    while (true);                   // if failed, do nothing
-  }
-  LoRa.sleep();
-  LoRa.setSyncWord(syncWord);
-  LoRa.idle();
-   // register the receive callback
-  LoRa.onReceive(onReceive);
-
-  // put the radio into receive mode
-  LoRa.receive();
-  LoRa.setTimeout(10);              // set Stream timeout of 10ms
-  Serial.println("LoRa init succeeded.");
-
-  Serial.println("Sync Word:" + String(syncWord, HEX));
-  Serial.println("Local Addr:" + String(localAddress, HEX));
-  Serial.println();
-  Serial.print("Received from:\t");
-  Serial.print("Sent to:\t");
-  Serial.print("Message ID:\t");
-  Serial.print("Message length:\t");
-  Serial.print("Message:\t");
-  Serial.print("Sender's sync word:\t");
-  Serial.print("RSSI:\t");
-  Serial.println("Snr:");
-}
-
-void loop() {
-  if (millis() - lastSend > 500) {
-    message = "sender's syncWord:\t";  // send a message; tab automatically
-    message += String(syncWord, HEX);  // separates the sync word into its own column
-    sendMessage(message);
-    lastSend = millis();
-  }
-  //  Change the sync word once every 10 messages:
-  //if(messageId % 10 == 0 && change == 1) {
-  //  LoRa.sleep();
-  //  LoRa.setSyncWord(syncWord++);
-  //  LoRa.idle();
-  //}
-}
-
-void sendMessage(String outgoing) {
-  LoRa.beginPacket();                   // start packet
-  LoRa.write(destination);              // add destination address
-  LoRa.write(localAddress);             // add sender address
-  LoRa.write(messageId);                // add message ID
-  LoRa.write(outgoing.length());        // add payload length
-  LoRa.print(outgoing);                 // add payload
-  LoRa.endPacket();                     // finish packet and send it
-  messageId++;                          // increment message ID
-}
-
-
-void onReceive(int packetSize) {
-  // read packet header bytes:
-  int recipient = LoRa.read();       // recipient address
-  byte sender = LoRa.read();          // sender address
-  byte latestMessage = LoRa.read();   // incoming msg ID
-  byte msgLength = LoRa.read();       // incoming msg length
-  String incoming = LoRa.readString();// payload of packet
-
-  if (msgLength != incoming.length()) {   // check length for error
-    Serial.println("error: message length does not match length");
-  }
-  // if the recipient isn't this device or broadcast,
-  if (recipient != localAddress && recipient != 0xFF) {
-    Serial.println("This message is not for me.");
-    return;           // skip rest of loop
-  }
-  // if message is for this device, or broadcast, print details:
-  Serial.print(sender, HEX);
-  Serial.print("\t");
-  Serial.print(recipient, HEX);
-  Serial.print("\t");
-  Serial.print(latestMessage);
-  Serial.print("\t");
-  Serial.print(msgLength);
-  Serial.print("\t");
-  Serial.print(incoming);
-  Serial.print("\t");
-  Serial.print(LoRa.packetRssi());  // print RSSI of packet
-  Serial.print("\t");
-  Serial.print(LoRa.packetSnr());
-  Serial.println();
-}
-