By default we now search for substrings; you can search for multiple substrings
by separating them with spaces. Add a config option gui.filterMode that can be
set to 'fuzzy' to switch back to the previous behavior.
It sorts them already, so it's unnecessary. In the next commit we use this same
code for substring searching too, and in that case we don't want to sort because
sorting is by Score, but we don't even fill in the score for substring
searching.
Lazygit has two ways to decide whether it needs to ask the user to force-push:
1. if it knows ahead of time that the push will fail because the branch has
diverged, by looking at the incoming/outgoing information that it shows as ↑3↓7.
2. by examining the error that comes back when the push has failed.
The second situation should happen only rarely, because lazygit fetches every
minute by default, so the ↑3↓7 information is usually up to date. It might not
be if the user turned off auto-fetch (or increased the auto-fetch interval).
However, in this case it's almost always harmful to prompt the user to
force-push, because we know that the reason for diverging is that something was
pushed to the remote, and we would wipe it out by force-pushing. In such a
situation, the more likely user action is to pull the remote changes and then
push normally again.
So just remove the second prompt, and replace it by a better error message when
we detect that updates were rejected remotely.
A little bit of history archeology reveals that the second prompt was added at a
time where we didn't have the first one yet, so at that time it made sense to
have it; but when the first prompt was added, we should have removed the second.
So far, the only situation where we called SetSelectionRangeAndMode was one
where the range could only get larger (in startInteractiveRebaseWithEdit, in
which case update-ref todos can be inserted by the rebase). However, in the last
commit we introduced a new call site where the range can get smaller, including
being reduced to a single item. Since this is indistinguishable from a single
selection, set the mode to none in this case; without this, hitting escape would
seemingly do nothing because it collapses the empty range selection.
... and when recalling a commit message from an old commit by pressing up-arrow.
This is necessary because committing turns our soft line breaks into real ones,
but when rewording we want to turn them back into soft ones again, so that it's
possible to insert words at the beginning of a paragraph and have everything
rewrap nicely.
This is only a best effort; the algorithm only removes those hard line breaks
that can be removed without changing the way the message looks. This works well
when the previous commit message was wrapped at the same width, which for most
users should be the most common case; but if it wasn't, the result is not great.
Specifically, if the old wrap width was smaller, some hard line breaks just
won't be removed; if it was wider though, you'll get an unpleasant comb effect
with alternating long and short lines. In such a case it's best to switch to the
editor and use whatever wrapping features you have there (e.g. alt-Q).
I have seen some commit messages that contain CRLF instead of just LF; I'm not
sure if these were created by a broken git client, but they exist, so we need to
deal with them. Editing them when rewording a commit sort of works, but is a
little strange; the \r characters are invisble, so you need an extra arrow key
press to skip over them.
In the next commit we are going to add more logic related to line breaks, and it
is getting confused by the \r, so it is becoming more important to fix this. The
easiest fix is to normalize the line endings right after loading.
This should arguably have been done in b133318b40 already; it's becoming more
important now because we're going to extend the common code with more logic in
the next commit.
We have such a test already (squash_fixups_above_first_commit.go), but it can't
be used for what we want to check here, because it uses the first commit, and we
can't move down from there. So create a new one that basically does the same
thing, but for a commit in the middle. The focus of this new test is to check
how the selection behaves; as you can see, there is a problem both when creating
a fixup and when squashing fixups. We'll address these separately in the next
commits.
It starts a rebase on the bottom-most commit of the range, and sets all the
selected commits to "edit" (skipping merge commits, because they can't be
edited).
In most real-world scenarios, name and path are usually the same. They don't
have to be though, and it's important to make sure we use the right one when
passing arguments to git commands, so change the tests to have different name
and path.
When doing a non-interactive rebase using a version of git earlier than 2.26, or
by explicitly calling `git -c rebase.backend=apply rebase`, lazygit can display
the pending todos by parsing the numbered patch files in `.git/rebase-apply/`.
Unfortunately, support for this has been broken for more than three years
because of the change in 682db77401 (the string literal "normal" should have
been changed to REBASE_MODE_NORMAL instead of REBASE_MODE_MERGING).
It's not an important bug since you can only get into this situation by doing a
rebase outside of lazygit, and then only with a pretty old git version or by
using very uncommon git options. So instead of fixing the bug, just remove the
code.
This makes it possible again to pass multiple arguments, for example
"--ff-only --autostash". This won't work correctly if you want to use
an argument that contains a space, but it's very unlikely that people
will want to do that, so I think this is good enough.
The additional branch head icon is more confusing than useful in this situation.
The update-ref entries show very clearly where the branch heads will go when
continuing the rebase; the information where the branch heads used to be before
the rebase is not really needed here, and just makes the display more confusing.
I'm not adding more tests here because the changes to the existing tests
demonstrate the change clearly enough.
The helix binary seems to be called "helix" on some distributions (e.g. Arch),
but "hx" on others (e.g. Fedora). Provide presets for both, so that
auto-detection from $EDITOR works.
A common workflow for me is to create a fixup commit from only some of my
current changes; to do that, I enter a file, stage a few hunks, and then want to
invoke ctrl-f to find the base commit for these changes. Currently I need to esc
back to the files panel in order to do that; it's more convenient to be able to
do this right from the staging panel.
This commit introduces a new feature to the commit view, allowing users
to filter commits based on the author's name or email address. Similar
to the existing path filtering functionality, accessible through <c-s>,
this feature allows users to filter the commit history by the currently
selected commit's author if the commit view is focused, or by typing in
the author's name or email address.
This feature adds an entry to the filtering menu, to provide users with
a familiar and intuitive experience
