If the input buffer exceeds the stack auxiliary buffer, qsort will
malloc a temporary one to call mergesort. Since C++ standard does
allow the callback comparison function to throw [1], the glibc
implementation can potentially leak memory.
The fixes uses a pthread_cleanup_combined_push and
pthread_cleanup_combined_pop, so it can work with and without
exception enables. The qsort code path that calls malloc now
requires some extra setup and a call to __pthread_cleanup_push
anmd __pthread_cleanup_pop (which should be ok since they just
setup some buffer state).
Checked on x86_64-linux-gnu.
[1] https://timsong-cpp.github.io/cppwp/n4950/alg.c.library#4
Reviewed-by: DJ Delorie <dj@redhat.com>
If some shared library loaded with dlopen/dlmopen requires an executable
stack, either implicitly because of a missing GNU_STACK ELF header
(where the ABI default flags implies in the executable bit) or explicitly
because of the executable bit from GNU_STACK; the loader will try to set
the both the main thread and all thread stacks (from the pthread cache)
as executable.
Besides the issue where any __nptl_change_stack_perm failure does not
undo the previous executable transition (meaning that if the library
fails to load, there can be thread stacks with executable stacks), this
behavior was used on a CVE [1] as a vector for RCE.
This patch changes that if a shared library requires an executable
stack, and the current stack is not executable, dlopen fails. The
change is done only for dynamically loaded modules, if the program
or any dependency requires an executable stack, the loader will still
change the main thread before program execution and any thread created
with default stack configuration.
[1] https://www.qualys.com/2023/07/19/cve-2023-38408/rce-openssh-forwarded-ssh-agent.txt
Checked on x86_64-linux-gnu and i686-linux-gnu.
Reviewed-by: Florian Weimer <fweimer@redhat.com>
The recursive lock used on abort does not synchronize with a new process
creation (either by fork-like interfaces or posix_spawn ones), nor it
is reinitialized after fork().
Also, the SIGABRT unblock before raise() shows another race condition,
where a fork or posix_spawn() call by another thread, just after the
recursive lock release and before the SIGABRT signal, might create
programs with a non-expected signal mask. With the default option
(without POSIX_SPAWN_SETSIGDEF), the process can see SIG_DFL for
SIGABRT, where it should be SIG_IGN.
To fix the AS-safe, raise() does not change the process signal mask,
and an AS-safe lock is used if a SIGABRT is installed or the process
is blocked or ignored. With the signal mask change removal,
there is no need to use a recursive loc. The lock is also taken on
both _Fork() and posix_spawn(), to avoid the spawn process to see the
abort handler as SIG_DFL.
A read-write lock is used to avoid serialize _Fork and posix_spawn
execution. Both sigaction (SIGABRT) and abort() requires to lock
as writer (since both change the disposition).
The fallback is also simplified: there is no need to use a loop of
ABORT_INSTRUCTION after _exit() (if the syscall does not terminate the
process, the system is broken).
The proposed fix changes how setjmp works on a SIGABRT handler, where
glibc does not save the signal mask. So usage like the below will now
always abort.
static volatile int chk_fail_ok;
static jmp_buf chk_fail_buf;
static void
handler (int sig)
{
if (chk_fail_ok)
{
chk_fail_ok = 0;
longjmp (chk_fail_buf, 1);
}
else
_exit (127);
}
[...]
signal (SIGABRT, handler);
[....]
chk_fail_ok = 1;
if (! setjmp (chk_fail_buf))
{
// Something that can calls abort, like a failed fortify function.
chk_fail_ok = 0;
printf ("FAIL\n");
}
Such cases will need to use sigsetjmp instead.
The _dl_start_profile calls sigaction through _profil, and to avoid
pulling abort() on loader the call is replaced with __libc_sigaction.
Checked on x86_64-linux-gnu and aarch64-linux-gnu.
Reviewed-by: DJ Delorie <dj@redhat.com>
The current racy approach is to enable asynchronous cancellation
before making the syscall and restore the previous cancellation
type once the syscall returns, and check if cancellation has happen
during the cancellation entrypoint.
As described in BZ#12683, this approach shows 2 problems:
1. Cancellation can act after the syscall has returned from the
kernel, but before userspace saves the return value. It might
result in a resource leak if the syscall allocated a resource or a
side effect (partial read/write), and there is no way to program
handle it with cancellation handlers.
2. If a signal is handled while the thread is blocked at a cancellable
syscall, the entire signal handler runs with asynchronous
cancellation enabled. This can lead to issues if the signal
handler call functions which are async-signal-safe but not
async-cancel-safe.
For the cancellation to work correctly, there are 5 points at which the
cancellation signal could arrive:
[ ... )[ ... )[ syscall ]( ...
1 2 3 4 5
1. Before initial testcancel, e.g. [*... testcancel)
2. Between testcancel and syscall start, e.g. [testcancel...syscall start)
3. While syscall is blocked and no side effects have yet taken
place, e.g. [ syscall ]
4. Same as 3 but with side-effects having occurred (e.g. a partial
read or write).
5. After syscall end e.g. (syscall end...*]
And libc wants to act on cancellation in cases 1, 2, and 3 but not
in cases 4 or 5. For the 4 and 5 cases, the cancellation will eventually
happen in the next cancellable entrypoint without any further external
event.
The proposed solution for each case is:
1. Do a conditional branch based on whether the thread has received
a cancellation request;
2. It can be caught by the signal handler determining that the saved
program counter (from the ucontext_t) is in some address range
beginning just before the "testcancel" and ending with the
syscall instruction.
3. SIGCANCEL can be caught by the signal handler and determine that
the saved program counter (from the ucontext_t) is in the address
range beginning just before "testcancel" and ending with the first
uninterruptable (via a signal) syscall instruction that enters the
kernel.
4. In this case, except for certain syscalls that ALWAYS fail with
EINTR even for non-interrupting signals, the kernel will reset
the program counter to point at the syscall instruction during
signal handling, so that the syscall is restarted when the signal
handler returns. So, from the signal handler's standpoint, this
looks the same as case 2, and thus it's taken care of.
5. For syscalls with side-effects, the kernel cannot restart the
syscall; when it's interrupted by a signal, the kernel must cause
the syscall to return with whatever partial result is obtained
(e.g. partial read or write).
6. The saved program counter points just after the syscall
instruction, so the signal handler won't act on cancellation.
This is similar to 4. since the program counter is past the syscall
instruction.
So The proposed fixes are:
1. Remove the enable_asynccancel/disable_asynccancel function usage in
cancellable syscall definition and instead make them call a common
symbol that will check if cancellation is enabled (__syscall_cancel
at nptl/cancellation.c), call the arch-specific cancellable
entry-point (__syscall_cancel_arch), and cancel the thread when
required.
2. Provide an arch-specific generic system call wrapper function
that contains global markers. These markers will be used in
SIGCANCEL signal handler to check if the interruption has been
called in a valid syscall and if the syscalls has side-effects.
A reference implementation sysdeps/unix/sysv/linux/syscall_cancel.c
is provided. However, the markers may not be set on correct
expected places depending on how INTERNAL_SYSCALL_NCS is
implemented by the architecture. It is expected that all
architectures add an arch-specific implementation.
3. Rewrite SIGCANCEL asynchronous handler to check for both canceling
type and if current IP from signal handler falls between the global
markers and act accordingly.
4. Adjust libc code to replace LIBC_CANCEL_ASYNC/LIBC_CANCEL_RESET to
use the appropriate cancelable syscalls.
5. Adjust 'lowlevellock-futex.h' arch-specific implementations to
provide cancelable futex calls.
Some architectures require specific support on syscall handling:
* On i386 the syscall cancel bridge needs to use the old int80
instruction because the optimized vDSO symbol the resulting PC value
for an interrupted syscall points to an address outside the expected
markers in __syscall_cancel_arch. It has been discussed in LKML [1]
on how kernel could help userland to accomplish it, but afaik
discussion has stalled.
Also, sysenter should not be used directly by libc since its calling
convention is set by the kernel depending of the underlying x86 chip
(check kernel commit 30bfa7b3488bfb1bb75c9f50a5fcac1832970c60).
* mips o32 is the only kABI that requires 7 argument syscall, and to
avoid add a requirement on all architectures to support it, mips
support is added with extra internal defines.
Checked on aarch64-linux-gnu, arm-linux-gnueabihf, powerpc-linux-gnu,
powerpc64-linux-gnu, powerpc64le-linux-gnu, i686-linux-gnu, and
x86_64-linux-gnu.
[1] https://lkml.org/lkml/2016/3/8/1105
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
And make always supported. The configure option was added on glibc 2.25
and some features require it (such as hwcap mask, huge pages support, and
lock elisition tuning). It also simplifies the build permutations.
Changes from v1:
* Remove glibc.rtld.dynamic_sort changes, it is orthogonal and needs
more discussion.
* Cleanup more code.
Reviewed-by: Siddhesh Poyarekar <siddhesh@sourceware.org>
Replace the 3 uses of atomic_bit_set and atomic_bit_test_set with
atomic_fetch_or_relaxed. Using relaxed MO is correct since the
atomics are used to ensure memory is released only once.
Reviewed-by: Florian Weimer <fweimer@redhat.com>
Some Linux interfaces never restart after being interrupted by a signal
handler, regardless of the use of SA_RESTART [1]. It means that for
pthread cancellation, if the target thread disables cancellation with
pthread_setcancelstate and calls such interfaces (like poll or select),
it should not see spurious EINTR failures due the internal SIGCANCEL.
However recent changes made pthread_cancel to always sent the internal
signal, regardless of the target thread cancellation status or type.
To fix it, the previous semantic is restored, where the cancel signal
is only sent if the target thread has cancelation enabled in
asynchronous mode.
The cancel state and cancel type is moved back to cancelhandling
and atomic operation are used to synchronize between threads. The
patch essentially revert the following commits:
8c1c0aae20 nptl: Move cancel type out of cancelhandling
2b51742531 nptl: Move cancel state out of cancelhandling
26cfbb7162 nptl: Remove CANCELING_BITMASK
However I changed the atomic operation to follow the internal C11
semantic and removed the MACRO usage, it simplifies a bit the
resulting code (and removes another usage of the old atomic macros).
Checked on x86_64-linux-gnu, i686-linux-gnu, aarch64-linux-gnu,
and powerpc64-linux-gnu.
[1] https://man7.org/linux/man-pages/man7/signal.7.html
Reviewed-by: Florian Weimer <fweimer@redhat.com>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
I used these shell commands:
../glibc/scripts/update-copyrights $PWD/../gnulib/build-aux/update-copyright
(cd ../glibc && git commit -am"[this commit message]")
and then ignored the output, which consisted lines saying "FOO: warning:
copyright statement not found" for each of 7061 files FOO.
I then removed trailing white space from math/tgmath.h,
support/tst-support-open-dev-null-range.c, and
sysdeps/x86_64/multiarch/strlen-vec.S, to work around the following
obscure pre-commit check failure diagnostics from Savannah. I don't
know why I run into these diagnostics whereas others evidently do not.
remote: *** 912-#endif
remote: *** 913:
remote: *** 914-
remote: *** error: lines with trailing whitespace found
...
remote: *** error: sysdeps/unix/sysv/linux/statx_cp.c: trailing lines
We stopped adding "Contributed by" or similar lines in sources in 2012
in favour of git logs and keeping the Contributors section of the
glibc manual up to date. Removing these lines makes the license
header a bit more consistent across files and also removes the
possibility of error in attribution when license blocks or files are
copied across since the contributed-by lines don't actually reflect
reality in those cases.
Move all "Contributed by" and similar lines (Written by, Test by,
etc.) into a new file CONTRIBUTED-BY to retain record of these
contributions. These contributors are also mentioned in
manual/contrib.texi, so we just maintain this additional record as a
courtesy to the earlier developers.
The following scripts were used to filter a list of files to edit in
place and to clean up the CONTRIBUTED-BY file respectively. These
were not added to the glibc sources because they're not expected to be
of any use in future given that this is a one time task:
https://gist.github.com/siddhesh/b5ecac94eabfd72ed2916d6d8157e7dchttps://gist.github.com/siddhesh/15ea1f5e435ace9774f485030695ee02
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
This commit also moves the aio_misc and aio_sigquue helper,
so GLIBC_PRIVATE exports need to be added.
The symbol was moved using scripts/move-symbol-to-libc.py.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This mirrors the situation on Hurd. These directories are on
the include search part, so #include <pthreadP.h> works after this
change on both Hurd and nptl.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
