InnoDB shutdown failed to properly take fil_crypt_thread() into account.
The encryption threads were signalled to shut down together with other
non-critical tasks. This could be much too early in case of slow shutdown,
which could need minutes to complete the purge. Furthermore, InnoDB
failed to wait for the fil_crypt_thread() to actually exit before
proceeding to the final steps of shutdown, causing the race conditions.
Furthermore, the log_scrub_thread() was shut down way too early.
Also it should remain until the SRV_SHUTDOWN_FLUSH_PHASE.
fil_crypt_threads_end(): Remove. This would cause the threads to
be terminated way too early.
srv_buf_dump_thread_active, srv_dict_stats_thread_active,
lock_sys->timeout_thread_active, log_scrub_thread_active,
srv_monitor_active, srv_error_monitor_active: Remove a race condition
between startup and shutdown, by setting these in the startup thread
that creates threads, not in each created thread. In this way, once the
flag is cleared, it will remain cleared during shutdown.
srv_n_fil_crypt_threads_started, fil_crypt_threads_event: Declare in
global rather than static scope.
log_scrub_event, srv_log_scrub_thread_active, log_scrub_thread():
Declare in static rather than global scope. Let these be created by
log_init() and freed by log_shutdown().
rotate_thread_t::should_shutdown(): Do not shut down before the
SRV_SHUTDOWN_FLUSH_PHASE.
srv_any_background_threads_are_active(): Remove. These checks now
exist in logs_empty_and_mark_files_at_shutdown().
logs_empty_and_mark_files_at_shutdown(): Shut down the threads in
the proper order. Keep fil_crypt_thread() and log_scrub_thread() alive
until SRV_SHUTDOWN_FLUSH_PHASE, and check that they actually terminate.
The upper limit of innodb_spin_wait_delay was ~0UL. It does not make
any sense to wait more than a few dozens of microseconds between
attempts to acquire a busy mutex.
Make the new upper limit 6000. ut_delay(6000) could correspond to
several milliseconds even today.
Problem was that log_scrub function did not take required log_sys mutex.
Background: Unused space in log blocks are padded with MLOG_DUMMY_RECORD if innodb-scrub-log
is enabled. As log files are written on circular fashion old log blocks can be reused
later for new redo-log entries. Scrubbing pads unused space in log blocks to avoid visibility
of the possible old redo-log contents.
log_scrub(): Take log_sys mutex
log_pad_current_log_block(): Increase srv_stats.n_log_scrubs if padding is done.
srv0srv.cc: Set srv_stats.n_log_scrubs to export vars innodb_scrub_log
ha_innodb.cc: Export innodb_scrub_log to global status.
The C preprocessor symbol WITH_NUMA is never defined. Instead, the symbol
HAVE_LIBNUMA is used for checking if the feature is to be used.
If cmake -DWITH_NUMA=OFF is specified, HAVE_LIBNUMA will not be defined
at compilation time even if the library is available.
If cmake -DWITH_NUMA=ON is specified but the library is not available
at configuration time, the compilation will be aborted.
This commit is for optimizing WSREP(thd) macro.
#define WSREP(thd) \
(WSREP_ON && wsrep && (thd && thd->variables.wsrep_on))
In this we can safely remove wsrep and thd. We are not removing WSREP_ON
because this will change WSREP(thd) behaviour.
Patch Credit:- Nirbhay Choubay, Sergey Vojtovich
The configuration parameter innodb_use_fallocate, which is mapped to
the variable srv_use_posix_fallocate, has no effect in MariaDB 10.2.2
or MariaDB 10.2.3.
Thus the configuration parameter and the variable should be removed.
fil_space_t::recv_size: New member: recovered tablespace size in pages;
0 if no size change was read from the redo log,
or if the size change was implemented.
fil_space_set_recv_size(): New function for setting space->recv_size.
innodb_data_file_size_debug: A debug parameter for setting the system
tablespace size in recovery even when the redo log does not contain
any size changes. It is hard to write a small test case that would
cause the system tablespace to be extended at the critical moment.
recv_parse_log_rec(): Note those tablespaces whose size is being changed
by the redo log, by invoking fil_space_set_recv_size().
innobase_init(): Correct an error message, and do not require a larger
innodb_buffer_pool_size when starting up with a smaller innodb_page_size.
innobase_start_or_create_for_mysql(): Allow startup with any initial
size of the ibdata1 file if the autoextend attribute is set. Require
the minimum size of fixed-size system tablespaces to be 640 pages,
not 10 megabytes. Implement innodb_data_file_size_debug.
open_or_create_data_files(): Round the system tablespace size down
to pages, not to full megabytes, (Our test truncates the system
tablespace to more than 800 pages with innodb_page_size=4k.
InnoDB should not imagine that it was truncated to 768 pages
and then overwrite good pages in the tablespace.)
fil_flush_low(): Refactored from fil_flush().
fil_space_extend_must_retry(): Refactored from
fil_extend_space_to_desired_size().
fil_mutex_enter_and_prepare_for_io(): Extend the tablespace if
fil_space_set_recv_size() was called.
The test case has been successfully run with all the
innodb_page_size values 4k, 8k, 16k, 32k, 64k.
This should be functionally equivalent to WL#6204 in MySQL 8.0.0, with
the notable difference that the file format changes are limited to
repurposing a previously unused data field in B-tree pages.
For persistent InnoDB tables, write the last used AUTO_INCREMENT
value to the root page of the clustered index, in the previously
unused (0) PAGE_MAX_TRX_ID field, now aliased as PAGE_ROOT_AUTO_INC.
Unlike some other previously unused InnoDB data fields, this one was
actually always zero-initialized, at least since MySQL 3.23.49.
The writes to PAGE_ROOT_AUTO_INC are protected by SX or X latch on the
root page. The SX latch will allow concurrent read access to the root
page. (The field PAGE_ROOT_AUTO_INC will only be read on the
first-time call to ha_innobase::open() from the SQL layer. The
PAGE_ROOT_AUTO_INC can only be updated when executing SQL, so
read/write races are not possible.)
During INSERT, the PAGE_ROOT_AUTO_INC is updated by the low-level
function btr_cur_search_to_nth_level(), adding no extra page
access. [Adaptive hash index lookup will be disabled during INSERT.]
If some rare UPDATE modifies an AUTO_INCREMENT column, the
PAGE_ROOT_AUTO_INC will be adjusted in a separate mini-transaction in
ha_innobase::update_row().
When a page is reorganized, we have to preserve the PAGE_ROOT_AUTO_INC
field.
During ALTER TABLE, the initial AUTO_INCREMENT value will be copied
from the table. ALGORITHM=COPY and online log apply in LOCK=NONE will
update PAGE_ROOT_AUTO_INC in real time.
innodb_col_no(): Determine the dict_table_t::cols[] element index
corresponding to a Field of a non-virtual column.
(The MySQL 5.7 implementation of virtual columns breaks the 1:1
relationship between Field::field_index and dict_table_t::cols[].
Virtual columns are omitted from dict_table_t::cols[]. Therefore,
we must translate the field_index of AUTO_INCREMENT columns into
an index of dict_table_t::cols[].)
Upgrade from old data files:
By default, the AUTO_INCREMENT sequence in old data files would appear
to be reset, because PAGE_MAX_TRX_ID or PAGE_ROOT_AUTO_INC would contain
the value 0 in each clustered index page. In new data files,
PAGE_ROOT_AUTO_INC can only be 0 if the table is empty or does not contain
any AUTO_INCREMENT column.
For backward compatibility, we use the old method of
SELECT MAX(auto_increment_column) for initializing the sequence.
btr_read_autoinc(): Read the AUTO_INCREMENT sequence from a new-format
data file.
btr_read_autoinc_with_fallback(): A variant of btr_read_autoinc()
that will resort to reading MAX(auto_increment_column) for data files
that did not use AUTO_INCREMENT yet. It was manually tested that during
the execution of innodb.autoinc_persist the compatibility logic is
not activated (for new files, PAGE_ROOT_AUTO_INC is never 0 in nonempty
clustered index root pages).
initialize_auto_increment(): Replaces
ha_innobase::innobase_initialize_autoinc(). This initializes
the AUTO_INCREMENT metadata. Only called from ha_innobase::open().
ha_innobase::info_low(): Do not try to lazily initialize
dict_table_t::autoinc. It must already have been initialized by
ha_innobase::open() or ha_innobase::create().
Note: The adjustments to class ha_innopart were not tested, because
the source code (native InnoDB partitioning) is not being compiled.
in slow shutdown mode purge threads really must exit only when there is
nothing to purge. Restore the trx_commit_disallowed check and
don't stop purge threads until all connection thread transactions
are gone.
Reduce the number of calls to encryption_get_key_get_latest_version
when doing key rotation with two different methods:
(1) We need to fetch key information when tablespace not yet
have a encryption information, invalid keys are handled now
differently (see below). There was extra call to detect
if key_id is not found on key rotation.
(2) If key_id is not found from encryption plugin, do not
try fetching new key_version for it as it will fail anyway.
We store return value from encryption_get_key_get_latest_version
call and if it returns ENCRYPTION_KEY_VERSION_INVALID there
is no need to call it again.
* remove old 5.2+ InnoDB support for virtual columns
* enable corresponding parts of the innodb-5.7 sources
* copy corresponding test cases from 5.7
* copy detailed Alter_inplace_info::HA_ALTER_FLAGS flags from 5.7
- and more detailed detection of changes in fill_alter_inplace_info()
* more "innodb compatibility hooks" in sql_class.cc to
- create/destroy/reset a THD (used by background purge threads)
- find a prelocked table by name
- open a table (from a background purge thread)
* different from 5.7:
- new service thread "thd_destructor_proxy" to make sure all THDs are
destroyed at the correct point in time during the server shutdown
- proper opening/closing of tables for vcol evaluations in
+ FK checks (use already opened prelocked tables)
+ purge threads (open the table, MDLock it, add it to tdc, close
when not needed)
- cache open tables in vc_templ
- avoid unnecessary allocations, reuse table->record[0] and table->s->default_values
- not needed in 5.7, because it overcalculates:
+ tell the server to calculate vcols for an on-going inline ADD INDEX
+ calculate vcols for correct error messages
* update other engines (mroonga/tokudb) accordingly
WL#7682 in MySQL 5.7 introduced the possibility to create light-weight
temporary tables in InnoDB. These are called 'intrinsic temporary tables'
in InnoDB, and in MySQL 5.7, they can be created by the optimizer for
sorting or buffering data in query processing.
In MariaDB 10.2, the optimizer temporary tables cannot be created in
InnoDB, so we should remove the dead code and related data structures.
innobase_kill_query(): Remove the bogus warning message
(for the valid outcome err==DB_DEADLOCK) that was added in
commit fec844aca8
Author: Jan Lindström <jan.lindstrom@mariadb.com>
Date: Tue Sep 6 09:43:16 2016 +0300
Merge InnoDB 5.7 from mysql-5.7.14.
Also, remove some redundant variables and add a debug assertion for
enforcing the proper outcome of lock_trx_handle_wait().
crashes server
This bug is the result of merging the Oracle MySQL follow-up fix
BUG#22963169 MYSQL CRASHES ON CREATE FULLTEXT INDEX
without merging the base bug fix:
Bug#79475 Insert a token of 84 4-bytes chars into fts index causes
server crash.
Unlike the above mentioned fixes in MySQL, our fix will not change
the storage format of fulltext indexes in InnoDB or XtraDB
when a character encoding with mbmaxlen=2 or mbmaxlen=3
and the length of a word is between 128 and 84*mbmaxlen bytes.
The Oracle fix would allocate 2 length bytes for these cases.
Compatibility with other MySQL and MariaDB releases is ensured by
persisting the used maximum length in the SYS_COLUMNS table in the
InnoDB data dictionary.
This fix also removes some unnecessary strcmp() calls when checking
for the legacy default collation my_charset_latin1
(my_charset_latin1.name=="latin1_swedish_ci").
fts_create_one_index_table(): Store the actual length in bytes.
This metadata will be written to the SYS_COLUMNS table.
fts_zip_initialize(): Initialize only the first byte of the buffer.
Actually the code should not even care about this first byte, because
the length is set as 0.
FTX_MAX_WORD_LEN: Define as HA_FT_MAXCHARLEN * 4 aka 336 bytes,
not as 254 bytes.
row_merge_create_fts_sort_index(): Set the actual maximum length of the
column in bytes, similar to fts_create_one_index_table().
row_merge_fts_doc_tokenize(): Remove the redundant parameter word_dtype.
Use the actual maximum length of the column. Calculate the extra_size
in the same way as row_merge_buf_encode() does.
crashes server
This bug is the result of merging the Oracle MySQL follow-up fix
BUG#22963169 MYSQL CRASHES ON CREATE FULLTEXT INDEX
without merging the base bug fix:
Bug#79475 Insert a token of 84 4-bytes chars into fts index causes
server crash.
Unlike the above mentioned fixes in MySQL, our fix will not change
the storage format of fulltext indexes in InnoDB or XtraDB
when a character encoding with mbmaxlen=2 or mbmaxlen=3
and the length of a word is between 128 and 84*mbmaxlen bytes.
The Oracle fix would allocate 2 length bytes for these cases.
Compatibility with other MySQL and MariaDB releases is ensured by
persisting the used maximum length in the SYS_COLUMNS table in the
InnoDB data dictionary.
This fix also removes some unnecessary strcmp() calls when checking
for the legacy default collation my_charset_latin1
(my_charset_latin1.name=="latin1_swedish_ci").
fts_create_one_index_table(): Store the actual length in bytes.
This metadata will be written to the SYS_COLUMNS table.
fts_zip_initialize(): Initialize only the first byte of the buffer.
Actually the code should not even care about this first byte, because
the length is set as 0.
FTX_MAX_WORD_LEN: Define as HA_FT_MAXCHARLEN * 4 aka 336 bytes,
not as 254 bytes.
row_merge_create_fts_sort_index(): Set the actual maximum length of the
column in bytes, similar to fts_create_one_index_table().
row_merge_fts_doc_tokenize(): Remove the redundant parameter word_dtype.
Use the actual maximum length of the column. Calculate the extra_size
in the same way as row_merge_buf_encode() does.
MySQL 5.7 introduced WL#7943: InnoDB: Implement Information_Schema.Files
to provide a long-term alternative for accessing tablespace metadata.
The INFORMATION_SCHEMA.INNODB_* views are considered internal interfaces
that are subject to change or removal between releases. So, users should
refer to I_S.FILES instead of I_S.INNODB_SYS_TABLESPACES to fetch metadata
about CREATE TABLESPACE.
Because MariaDB 10.2 does not support CREATE TABLESPACE or
CREATE TABLE…TABLESPACE for InnoDB, it does not make sense to support
I_S.FILES either. So, let MariaDB 10.2 omit the code that was added in
MySQL 5.7. After this change, I_S.FILES will report the empty result,
unless some other storage engine in MariaDB 10.2 implements the interface.
(The I_S.FILES interface was originally created for the NDB Cluster.)
In functions that declare pointer parameters as nonnull,
remove nullness checks, because GCC would optimize them away anyway.
Use #ifdef instead of #if when checking for a configuration flag.
Clang says that left shifts of negative values are undefined.
So, use ~0U instead of ~0 in a number of macros.
Some functions that were defined as UNIV_INLINE were declared as
UNIV_INTERN. Consistently use the same type of linkage.
ibuf_merge_or_delete_for_page() could pass bitmap_page=NULL to
buf_page_print(), conflicting with the __attribute__((nonnull)).
In InnoDB and XtraDB functions that declare pointer parameters as nonnull,
remove nullness checks, because GCC would optimize them away anyway.
Use #ifdef instead of #if when checking for a configuration flag.
Clang says that left shifts of negative values are undefined.
So, use ~0U instead of ~0 in a number of macros.
Some functions that were defined as UNIV_INLINE were declared as
UNIV_INTERN. Consistently use the same type of linkage.
ibuf_merge_or_delete_for_page() could pass bitmap_page=NULL to
buf_page_print(), conflicting with the __attribute__((nonnull)).
This is not a fix, this is instrumentation to find out is MySQL frm dictionary
and InnoDB data dictionary really out-of-sync when this assertion is fired,
or is there some other reason (bug).
With "WL#6047 - Do not allocate trx id for read-only transactions"
m_prebuilt->trx->id is always 0 for read-only transactions. This makes
it useless as an index for fuzzy counters.
Use server thread id instead similarly to MySQL.
for InnoDB tables"
Don't use thr_lock.c locks for InnoDB tables. Below is list of changes that
were needed to implement this:
- HANDLER OPEN acquireis MDL_SHARED_READ instead of MDL_SHARED
- HANDLER READ calls external_lock() even if SE is not going to be locked by
THR_LOCK
- InnoDB lock wait timeouts are now honored which are much shorter by default
than server lock wait timeouts (1 year vs 50 seconds)
- with @@autocommit= 1 LOCK TABLES disables autocommit implicitely, though
user still sees @@autocommt= 1
- the above starts implicit transaction
- transactions started by LOCK TABLES are now rolled back on disconnect
(previously everything was committed due to autocommit)
- transactions started by LOCK TABLES are now rolled back by ROLLBACK
(previously everything was committed due to autocommit)
- it is now impossible to change BINLOG_FORMAT under LOCK TABLES (at least
to statement) due to running transaction
- LOCK TABLES WRITE is additionally handled by MDL
- ...in contrast LOCK TABLES READ protection against DML is pure InnoDB
- combining transactional and non-transactional tables under LOCK TABLES
may cause rolled back changes in transactional table and "committed"
changes in non-transactional table
- user may disable innodb_table_locks, which will cause LOCK TABLES to be
noop basically
Removed tests for BUG#45143 and BUG#55930 which cover InnoDB + THR_LOCK. To
operate properly these tests require code flow to go through THR_LOCK debug
sync points, which is not the case after this patch. These tests are removed
by WL#6671 as well. An alternative is to port them to different storage engine.
Two problems:
(1) When pushing warning to sql-layer we need to check that thd != NULL
to avoid NULL-pointer reference.
(2) At tablespace key rotation if used key_id is not found from
encryption plugin tablespace should not be rotated.
