IN TIME RECOVERY FAILURE ON SLAVES
Problem:
DROP TEMP TABLE IF EXISTS commands can cause point
in time recovery (re-applying binlog) failures.
Analyses:
In RBR, 'DROP TEMPORARY TABLE' commands are
always binlogged by adding 'IF EXISTS' clauses.
Also, the slave SQL thread will not check replicate.* filter
rules for "DROP TEMPORARY TABLE IF EXISTS" queries.
If log-slave-updates is enabled on slave, these queries
will be binlogged in the format of "USE `db`;
DROP TEMPORARY TABLE IF EXISTS `t1`;" irrespective
of filtering rules and irrespective of the `db` existence.
When users try to recover slave from it's own binlog,
use `db` command might fail if `db` is not present on slave.
Fix:
At the time of writing the 'DROP TEMPORARY TABLE
IF EXISTS' query into the binlog, 'use `db`' will not be
present and the table name in the query will be a fully
qualified table name.
Eg:
'USE `db`; DROP TEMPORARY TABLE IF EXISTS `t1`;'
will be logged as
'DROP TEMPORARY TABLE IF EXISTS `db`.`t1`;'.
Major replication test framework cleanup. This does the following:
- Ensure that all tests clean up the replication state when they
finish, by making check-testcase check the output of SHOW SLAVE STATUS.
This implies:
- Slave must not be running after test finished. This is good
because it removes the risk for sporadic errors in subsequent
tests when a test forgets to sync correctly.
- Slave SQL and IO errors must be cleared when test ends. This is
good because we will notice if a test gets an unexpected error in
the slave threads near the end.
- We no longer have to clean up before a test starts.
- Ensure that all tests that wait for an error in one of the slave
threads waits for a specific error. It is no longer possible to
source wait_for_slave_[sql|io]_to_stop.inc when there is an error
in one of the slave threads. This is good because:
- If a test expects an error but there is a bug that causes
another error to happen, or if it stops the slave thread without
an error, then we will notice.
- When developing tests, wait_for_*_to_[start|stop].inc will fail
immediately if there is an error in the relevant slave thread.
Before this patch, we had to wait for the timeout.
- Remove duplicated and repeated code for setting up unusual replication
topologies. Now, there is a single file that is capable of setting
up arbitrary topologies (include/rpl_init.inc, but
include/master-slave.inc is still available for the most common
topology). Tests can now end with include/rpl_end.inc, which will clean
up correctly no matter what topology is used. The topology can be
changed with include/rpl_change_topology.inc.
- Improved debug information when tests fail. This includes:
- debug info is printed on all servers configured by include/rpl_init.inc
- User can set $rpl_debug=1, which makes auxiliary replication files
print relevant debug info.
- Improved documentation for all auxiliary replication files. Now they
describe purpose, usage, parameters, and side effects.
- Many small code cleanups:
- Made have_innodb.inc output a sensible error message.
- Moved contents of rpl000017-slave.sh into rpl000017.test
- Added mysqltest variables that expose the current state of
disable_warnings/enable_warnings and friends.
- Too many to list here: see per-file comments for details.
temp table
This patch introduces two key changes in the replication's behavior.
Firstly, it reverts part of BUG#51894 which puts any update to temporary tables
into the trx-cache. Now, updates to temporary tables are handled according to
the type of their engines as a regular table.
Secondly, an unsafe mixed statement, (i.e. a statement that access transactional
table as well non-transactional or temporary table, and writes to any of them),
are written into the trx-cache in order to minimize errors in the execution when
the statement logging format is in use.
Such changes has a direct impact on which statements are classified as unsafe
statements and thus part of BUG#53259 is reverted.
Some of the test cases reference to binlog position and
these position numbers are written into result explicitly.
It is difficult to maintain if log event format changes.
There are a couple of cases explicit position number appears,
we handle them in different ways
A. 'CHANGE MASTER ...' with MASTER_LOG_POS or/and RELAY_LOG_POS options
Use --replace_result to mask them.
B. 'SHOW BINLOG EVENT ...'
Replaced by show_binlog_events.inc or wait_for_binlog_event.inc.
show_binlog_events.inc file's function is enhanced by given
$binlog_file and $binlog_limit.
C. 'SHOW SLAVE STATUS', 'show_slave_status.inc' and 'show_slave_status2.inc'
For the test cases just care a few items in the result of 'SHOW SLAVE STATUS',
only the items related to each test case are showed.
'show_slave_status.inc' is rebuild, only the given items in $status_items
will be showed.
'check_slave_is_running.inc' and 'check_slave_no_error.inc'
and 'check_slave_param.inc' are auxiliary files helping
to show running status and error information easily.
transaction
BUG#52616 Temp table prevents switch binlog format from STATEMENT to ROW
Before the WL#2687 and BUG#46364, every non-transactional change that happened
after a transactional change was written to trx-cache and flushed upon
committing the transaction. WL#2687 and BUG#46364 changed this behavior and
non-transactional changes are now written to the binary log upon committing
the statement.
A binary log event is identified as transactional or non-transactional through
a flag in the Log_event which is set taking into account the underlie storage
engine on what it is stems from. In the current bug, this flag was not being
set properly when the DROP TEMPORARY TABLE was executed.
However, while fixing this bug we figured out that changes to temporary tables
should be always written to the trx-cache if there is an on-going transaction.
Otherwise, binlog events in the reversed order would be produced.
Regarding concurrency, keeping changes to temporary tables in the trx-cache is
also safe as temporary tables are only visible to the owner connection.
In this patch, we classify the following statements as unsafe:
1 - INSERT INTO t_myisam SELECT * FROM t_myisam_temp
2 - INSERT INTO t_myisam_temp SELECT * FROM t_myisam
3 - CREATE TEMPORARY TABLE t_myisam_temp SELECT * FROM t_myisam
On the other hand, the following statements are classified as safe:
1 - INSERT INTO t_innodb SELECT * FROM t_myisam_temp
2 - INSERT INTO t_myisam_temp SELECT * FROM t_innodb
The patch also guarantees that transactions that have a DROP TEMPORARY are
always written to the binary log regardless of the mode and the outcome:
commit or rollback. In particular, the DROP TEMPORARY is extended with the
IF EXISTS clause when the current statement logging format is set to row.
Finally, the patch allows to switch from STATEMENT to MIXED/ROW when there
are temporary tables but the contrary is not possible.
