GTID events are applied without a running server transaction,
we need to set next transaction ID for Wsrep transaction.
The whole Galera cluster now has a single GTID value (including
the server ID throughout the cluster), fix the config accordingly.
Add force restart so that repeated MTR test execution prints
consistent GTID values, otherwise they would have been recovered
from the previous run.
Signed-off-by: Julius Goryavsky <julius.goryavsky@mariadb.com>
It's possible to establish Galera multi-cluster setups connected
through the native replication when every Galera cluster is configured
to have a separate domain ID.
For this setup to work, we need to replace domain ID values in generated
GTID events when they are written at transaction commit to the values
configured by Wsrep replication.
At the same time, it's possible that the GTID event already contains
a correct domain ID if it comes through the native replication from
another Galera cluster.
In this case, when such an event is applied either through a native
replication slave thread or through Wsrep applier, we write GTID event
on transaction start and avoid writing it during transaction commit.
The code contained multiple problems that were fixed:
- applying GTID events didn't work because it's applied without a
running server transaction and Wsrep transaction was not started
- GTID event generation on transaction start didn't contain proper
"standalone" and "is_transactional" flags that the original applied
GTID event contained
- condition determining that GTID event is written on transaction start
to avoid writing it on commit relied on the fact that the GTID event
is the first found in transaction/statement caches, which wasn't the
case and resulted in duplicate GTID events written
- instead of relying on the caches to find a GTID event, a simple check
is introduced that follows the exact rules for checking if event is
written at transaction start as described above
- the test case is improved to check that exact GTID events are
applied after two Galera clusters have synced.
Signed-off-by: Julius Goryavsky <julius.goryavsky@mariadb.com>
Support for galera GTID consistency thru cluster. All nodes in cluster
should have same GTID for replicated events which are originating from cluster.
Cluster originating commands need to contain sequential WSREP GTID seqno
Ignore manual setting of gtid_seq_no=X.
In master-slave scenario where master is non galera node replicated GTID is
replicated and is preserved in all nodes.
To have this - domain_id, server_id and seqnos should be same on all nodes.
Node which bootstraps the cluster, to achieve this, sends domain_id and
server_id to other nodes and this combination is used to write GTID for events
that are replicated inside cluster.
Cluster nodes that are executing non replicated events are going to have different
GTID than replicated ones, difference will be visible in domain part of gtid.
With wsrep_gtid_domain_id you can set domain_id for WSREP cluster.
Functions WSREP_LAST_WRITTEN_GTID, WSREP_LAST_SEEN_GTID and
WSREP_SYNC_WAIT_UPTO_GTID now works with "native" GTID format.
Fixed galera tests to reflect this chances.
Add variable to manually update WSREP GTID seqno in cluster
Add variable to manipulate and change WSREP GTID seqno. Next command
originating from cluster and on same thread will have set seqno and
cluster should change their internal counter to it's value.
Behavior is same as using @@gtid_seq_no for non WSREP transaction.
Temporary disable WSREP while executing RESET MASTER. In situation when 2 nodes are both master/slave first stop slave on both and than reset master.
Enforce stricter causality check with wsrep_sync_wait.
Problem:- Gtid are not transferred in Galera Cluster.
Solution:- We need to transfer gtid in the case on either when cluster is
slave/master in async replication. In normal Gtid replication gtid are generated on
recieving node itself and it is always on sync with other nodes. Because galera keeps
node in sync , So all nodes get same no of event groups. So the issue arises when
say galera is slave in async replication.
A
| (Async replication)
D <-> E <-> F {Galera replication}
So what should happen is that all node should apply the master gtid but this does
node happen, becuase node E, F does not recieve gtid from D in write set , So what E(or F)
does is that it applies wsrep_gtid_domain_id, D server-id , E gtid next seq no. This
generated gtid does not always work when say A has different domain id.
So In this commit, on galera node when we see that this event is recieved from master
we simply write Gtid_Log_Event in write_set and send it to other nodes.
