Modifications for ATtiny4x2, at least as far as compilation.

Eliminate RTC-based LED flashing code in favor of busy loop, which is significantly shorter now that peripherals are not in range of quick IO instructions.
Minor formatting changes while the code is young (notably spaces after the function name at the spot where they're actually defined, which makes them easier to search for.  Ancient corporate coding style guideline...)

optiboot/bootloaders/optiboot/optiboot_x.c

@@ -340,20 +340,12 @@ int main(void) {
 	}
     }
 
-#if LED_START_FLASHES > 0
-    // Set up RTC counting at about 1/8s (input is 32kHz)
-    while (RTC.STATUS & RTC_CTRLABUSY_bm)
-        ;  // RTC is used by startup logic (!) and might be busy.
-    RTC.CTRLA= RTC_PRESCALER_DIV4096_gc | RTC_RTCEN_bm;
-    RTC.DBGCTRL = 1; // enable during debug
-#endif
-
     _PROTECTED_WRITE(CLKCTRL.MCLKCTRLB, 0);  // full speed clock
 
     MYUART_TXPORT.DIR |= MYUART_TXPIN; // set TX pin to output
     MYUART_TXPORT.OUT |= MYUART_TXPIN;  // and "1" as per datasheet
 #if defined (MYUART_PMUX)
-    PORTMUX.USARTROUTEA |= MYUART_PMUX;  // alternate pinout to use
+    MYPMUX |= MYUART_PMUX;  // alternate pinout to use
 #endif
     MYUART.BAUD = BAUD_SETTING;
     MYUART.DBGCTRL = 1;  // run during debug
@@ -361,8 +353,8 @@ int main(void) {
     MYUART.CTRLA = 0;  // Interrupts: all off
     MYUART.CTRLB = USART_RXEN_bm | USART_TXEN_bm;
 
-    // Set up watchdog to trigger after 1s
+    // Set up watchdog to trigger after 8s
-//    watchdogConfig(WDT_PERIOD_1KCLK_gc);
+    watchdogConfig(WDT_PERIOD_8KCLK_gc);
 
 #if (LED_START_FLASHES > 0) || defined(LED_DATA_FLASH) || defined(LED_START_ON)
     /* Set LED pin as output */
@@ -431,7 +423,7 @@ int main(void) {
 	}
 	/* Write memory, length is big endian and is in bytes */
 	else if(ch == STK_PROG_PAGE) {
-	    // PROGRAM PAGE - we support flash programming only, not EEPROM
+	    // PROGRAM PAGE - any kind of page!
 	    uint8_t desttype;
 
 	    GETLENGTH(length);
@@ -442,6 +434,7 @@ int main(void) {
 	    } else {
 		address.word += MAPPED_EEPROM_START;
 	    }
+	    // TODO: user row?
 
 	    do {
 		*(address.bptr++) = getch();
@@ -469,6 +462,8 @@ int main(void) {
 	    } else {
 		address.word += MAPPED_EEPROM_START;
 	    }
+	    // TODO: user row?
+
 	    do {
 		putch(*(address.bptr++));
 	    } while (--length);
@@ -532,11 +527,15 @@ void verifySpace() {
 
 #if LED_START_FLASHES > 0
 void flash_led (uint8_t count) {
-    uint8_t last;
+#ifdef __INT24_MAX__
+    __uint24 delay;
+#else
+    uint32_t delay;
+# warning no uin24
+#endif
     while (count--) {
 	LED_PORT.IN |= LED;
-	last = RTC.CNTL & 1;
+	for (delay = (F_CPU/200); delay; delay--) {
-	while ((RTC.CNTL & 1) == last) {
 	    watchdogReset();
 	    if (MYUART.STATUS & USART_RXCIF_bm)
 		return;
@@ -550,8 +549,6 @@ void watchdogConfig(uint8_t x) {
 }
 
 
-
-
 #ifndef APP_NOSPM
 
 /*

optiboot/bootloaders/optiboot/pin_defs_x.h

@@ -670,6 +670,7 @@
 #define USART_ALTPMUX 1
 
 #if defined(__AVR_ATmega4809__)
+#define MYPMUX PORTMUX.USARTROUTEA
 # if (UARTTX == A0)
 #  ifndef USART0
 #   error Pin on USART0, but no USART0 exists
@@ -733,6 +734,36 @@
 # endif
 #endif  // ATmega4809
 
+/*
+ * 8pin Tiny0 and Tiny1
+ */
+#if defined(__AVR_ATtiny402__) || defined(__AVR_ATtiny202__) || \
+    defined(__AVR_ATtiny412__) || defined(__AVR_ATtiny212__)
+#define MYPMUX PORTMUX.CTRLB
+# if (UARTTX == A6)
+#  ifndef USART0
+#   error Pin on USART0, but no USART0 exists
+#  endif
+#  define MYUART USART0
+#  define MYUART_TXPORT VPORTA
+#  define MYUART_TXPIN (1<<PORT0)
+# elif (UARTTX == A1)
+#  ifndef USART0
+#   error Pin on USART0, but no USART0 exists
+#  endif
+#  define MYUART USART0
+#  define MYUART_TXPORT VPORTA
+#  define MYUART_TXPIN (1<<PORT4)
+#  define MYUART_PMUX (USART_ALTPMUX)
+# endif
+#endif // Tiny402/etc
+
+#if defined(__ATtiny3216__) || defined(__ATtiny1606__)
+#endif
+#if defined(__ATtiny1614__) || defined(__ATtiny1604__)
+#endif
+
+
 #ifndef MYUART
 # warning No UARTTX pin specified.
 #endif