Add basic ATtiny167 support. (LIN UART)

optiboot/bootloaders/optiboot/Makefile.tiny

@@ -274,3 +274,16 @@ attiny828at8_5v:
 	mv $(PROGRAM)_attiny828.lst $(PROGRAM)_$@.lst
 
 
+
+#-------------------
+# ATtiny167 - has LIN UART
+#--------------------
+
+
+attiny167: TARGET = attiny167
+attiny167: MCU_TARGET = attiny167
+attiny167: AVR_FREQ ?= 8000000L
+attiny167: CFLAGS += $(COMMON_OPTIONS) '-DVIRTUAL_BOOT_PARTITION' '-DBAUD_RATE=57600'
+attiny167: LDSECTIONS  = -Wl,--section-start=.text=0x1d80 -Wl,--section-start=.version=0x1ffe
+attiny167: $(PROGRAM)_attiny167.hex
+attiny167: $(PROGRAM)_attiny167.lst

optiboot/bootloaders/optiboot/optiboot.c

@@ -396,10 +396,10 @@ typedef uint8_t pagelen_t;
  * supress some compile-time options we want.)
  */
 
-int main(void) __attribute__ ((OS_main)) __attribute__ ((section (".init9")));
+int main(void) __attribute__ ((OS_main)) __attribute__ ((section (".init9"))) __attribute__((used));
 
-void __attribute__((noinline)) putch(char);
+void __attribute__((noinline)) __attribute__((leaf)) putch(char);
-uint8_t __attribute__((noinline)) getch(void);
+uint8_t __attribute__((noinline)) __attribute__((leaf)) getch(void) ;
 void __attribute__((noinline)) verifySpace();
 void __attribute__((noinline)) watchdogConfig(uint8_t x);
 
@@ -579,10 +579,19 @@ int main(void) {
       defined (__AVR_ATmega32__)
   #ifndef SINGLESPEED
   UCSRA = _BV(U2X); //Double speed mode USART
-#endif
+  #endif //singlespeed
   UCSRB = _BV(RXEN) | _BV(TXEN);  // enable Rx & Tx
   UCSRC = _BV(URSEL) | _BV(UCSZ1) | _BV(UCSZ0);  // config USART; 8N1
   UBRRL = (uint8_t)( (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 );
+  #else // mega8/etc
+    #ifdef LIN_UART
+  //DDRB|=3;
+  LINCR = (1 << LSWRES); 
+  //LINBRRL = (((F_CPU * 10L / 32L / BAUD_RATE) + 5L) / 10L) - 1; 
+  LINBRRL=(uint8_t)( (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 );
+  LINBTR = (1 << LDISR) | (8 << LBT0); 
+  LINCR = _BV(LENA) | _BV(LCMD2) | _BV(LCMD1) | _BV(LCMD0); 
+  LINDAT=0;
     #else
       #ifndef SINGLESPEED
   UART_SRA = _BV(U2X0); //Double speed mode USART0
@@ -590,8 +599,9 @@ int main(void) {
   UART_SRB = _BV(RXEN0) | _BV(TXEN0);
   UART_SRC = _BV(UCSZ00) | _BV(UCSZ01);
   UART_SRL = (uint8_t)( (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 );
-#endif
+    #endif // LIN_UART
-#endif
+  #endif // mega8/etc
+#endif // soft_uart
 
   // Set up watchdog to trigger after 1s
   watchdogConfig(WATCHDOG_1S);
@@ -806,8 +816,14 @@ int main(void) {
 
 void putch(char ch) {
 #ifndef SOFT_UART
-  while (!(UART_SRA & _BV(UDRE0)));
+  #ifndef LIN_UART
+    while (!(UART_SRA & _BV(UDRE0))) {  /* Spin */ }
+  #else
+    while (!(LINSIR & _BV(LTXOK)))   {  /* Spin */ }
+  #endif
+
   UART_UDR = ch;
+
 #else
   __asm__ __volatile__ (
     "   com %[ch]\n" // ones complement, carry set
@@ -874,9 +890,13 @@ uint8_t getch(void) {
       "r25"
 );
 #else
-  while(!(UART_SRA & _BV(RXC0)))
+#ifndef LIN_UART
-    ;
+  while(!(UART_SRA & _BV(RXC0)))  {  /* Spin */ }
   if (!(UART_SRA & _BV(FE0))) {
+#else
+  while(!(LINSIR & _BV(LRXOK)))  {  /* Spin */ }
+  if (!(LINSIR & _BV(LFERR))) {
+#endif
       /*
        * A Framing Error indicates (probably) that something is talking
        * to us at the wrong bit rate.  Assume that this is because it
@@ -960,7 +980,11 @@ void flash_led(uint8_t count) {
      *  quick succession, some of which will be lost and cause us to
      *  get out of sync.  So if we see any data; stop blinking.
      */
+#ifndef LIN_UART
     if (UART_SRA & _BV(RXC0))
+#else
+    if (LINSIR & _BV(LRXOK))
+#endif
 	break;
 #else
 // This doesn't seem to work?

optiboot/bootloaders/optiboot/pin_defs.h

@@ -43,11 +43,20 @@
  * differently.
  */
 #if UART == 0
+ #if defined(LINDAT)
+#define LIN_UART 1
+#define UART_SRA UCSRA
+#define UART_SRB UCSRB
+#define UART_SRC UCSRC
+#define UART_SRL UBRRL
+#define UART_UDR LINDAT
+ #else
 # define UART_SRA UCSR0A
 # define UART_SRB UCSR0B
 # define UART_SRC UCSR0C
 # define UART_SRL UBRR0L
 # define UART_UDR UDR0
+#endif
 #elif UART == 1
 #if !defined(UDR1)
 #error UART == 1, but no UART1 on device