Run new astyle formatter against all the examples

build/shared/examples/10.StarterKit/p14_TweakTheArduinoLogo/p14_TweakTheArduinoLogo.ino

@@ -1,23 +1,23 @@
 /*
   Arduino Starter Kit example
  Project 14  - Tweak the Arduino Logo
- 
+
  This sketch is written to accompany Project 14 in the
  Arduino Starter Kit
- 
+
  Parts required:
  10 kilohm potentiometer
- 
- Software required : 
+
+ Software required :
  Processing http://processing.org
  Active internet connection
- 
+
  Created 18 September 2012
  by Scott Fitzgerald
- 
+
  http://arduino.cc/starterKit
- 
- This example code is part of the public domain 
+
+ This example code is part of the public domain
  */
 
 
@@ -27,9 +27,9 @@ void setup() {
 }
 
 void loop() {
-  // read the value of A0, divide by 4 and 
+  // read the value of A0, divide by 4 and
   // send it as a byte over the serial connection
-  Serial.write(analogRead(A0)/4);
+  Serial.write(analogRead(A0) / 4);
   delay(1);
 }
 
@@ -37,68 +37,68 @@ void loop() {
  // Tweak the Arduno Logo
  // by Scott Fitzgerald
  // This example code is in the public domain
- 
+
  // import the serial library
  import processing.serial.*;
- 
+
  // create an instance of the serial library
  Serial myPort;
- 
+
  // create an instance of PImage
  PImage logo;
- 
+
  // a variable to hold the background color
  int bgcolor = 0;
- 
+
  void setup() {
  // set the color mode to Hue/Saturation/Brightness
  colorMode(HSB, 255);
- 
+
  // load the Arduino logo into the PImage instance
  logo = loadImage("http://arduino.cc/en/pub/skins/arduinoWide/img/logo.png");
- 
+
  // make the window the same size as the image
  size(logo.width, logo.height);
- 
- // print a list of available serial ports to the 
+
+ // print a list of available serial ports to the
  // Processing staus window
  println("Available serial ports:");
  println(Serial.list());
- 
+
  // Tell the serial object the information it needs to communicate
- // with the Arduno. Change Serial.list()[0] to the correct 
+ // with the Arduno. Change Serial.list()[0] to the correct
  // port corresponding to your Arduino board.  The last
  // parameter (e.g. 9600) is the speed of the communication.  It
  // has to correspond to the value passed to Serial.begin() in your
- // Arduino sketch.  
+ // Arduino sketch.
  myPort = new Serial(this, Serial.list()[0], 9600);
- 
+
  // If you know the name of the port used by the Arduino board, you
  // can specify it directly like this.
- // port = new Serial(this, "COM1", 9600);  
- 
+ // port = new Serial(this, "COM1", 9600);
+
  }
- 
+
  void draw() {
- 
+
  // if there is information in the serial port
  if ( myPort.available() > 0) {
  // read the value and store it in a variable
  bgcolor = myPort.read();
- 
+
  // print the value to the status window
- println(bgcolor); 
+ println(bgcolor);
  }
- 
+
  // Draw the background. the variable bgcolor
  // contains the Hue, determined by the value
  // from the serial port
  background(bgcolor, 255, 255);
- 
+
  // draw the Arduino logo
  image(logo, 0, 0);
  }
- 
+
  */