Run new astyle formatter against all the examples

build/shared/examples/01.Basics/AnalogReadSerial/AnalogReadSerial.ino

@@ -2,7 +2,7 @@
   AnalogReadSerial
   Reads an analog input on pin 0, prints the result to the serial monitor.
   Attach the center pin of a potentiometer to pin A0, and the outside pins to +5V and ground.
- 
+
  This example code is in the public domain.
  */
 

build/shared/examples/01.Basics/BareMinimum/BareMinimum.ino

@@ -4,6 +4,6 @@ void setup() {
 }
 
 void loop() {
-  // put your main code here, to run repeatedly: 
-  
+  // put your main code here, to run repeatedly:
+
 }

build/shared/examples/01.Basics/Blink/Blink.ino

@@ -1,18 +1,18 @@
 /*
   Blink
   Turns on an LED on for one second, then off for one second, repeatedly.
- 
+
   This example code is in the public domain.
  */
- 
+
 // Pin 13 has an LED connected on most Arduino boards.
 // give it a name:
 int led = 13;
 
 // the setup routine runs once when you press reset:
-void setup() {                
+void setup() {
   // initialize the digital pin as an output.
-  pinMode(led, OUTPUT);     
+  pinMode(led, OUTPUT);
 }
 
 // the loop routine runs over and over again forever:

build/shared/examples/01.Basics/DigitalReadSerial/DigitalReadSerial.ino

@@ -1,7 +1,7 @@
 /*
   DigitalReadSerial
- Reads a digital input on pin 2, prints the result to the serial monitor 
- 
+ Reads a digital input on pin 2, prints the result to the serial monitor
+
  This example code is in the public domain.
  */
 

build/shared/examples/01.Basics/Fade/Fade.ino

@@ -1,9 +1,9 @@
 /*
  Fade
- 
+
  This example shows how to fade an LED on pin 9
  using the analogWrite() function.
- 
+
  This example code is in the public domain.
  */
 
@@ -12,24 +12,24 @@ int brightness = 0;    // how bright the LED is
 int fadeAmount = 5;    // how many points to fade the LED by
 
 // the setup routine runs once when you press reset:
-void setup()  { 
+void setup() {
   // declare pin 9 to be an output:
   pinMode(led, OUTPUT);
-} 
+}
 
 // the loop routine runs over and over again forever:
-void loop()  { 
+void loop() {
   // set the brightness of pin 9:
-  analogWrite(led, brightness);    
+  analogWrite(led, brightness);
 
   // change the brightness for next time through the loop:
   brightness = brightness + fadeAmount;
 
-  // reverse the direction of the fading at the ends of the fade: 
+  // reverse the direction of the fading at the ends of the fade:
   if (brightness == 0 || brightness == 255) {
-    fadeAmount = -fadeAmount ; 
-  }     
-  // wait for 30 milliseconds to see the dimming effect    
-  delay(30);                            
+    fadeAmount = -fadeAmount ;
+  }
+  // wait for 30 milliseconds to see the dimming effect
+  delay(30);
 }
 

build/shared/examples/01.Basics/ReadAnalogVoltage/ReadAnalogVoltage.ino

@@ -2,7 +2,7 @@
   ReadAnalogVoltage
   Reads an analog input on pin 0, converts it to voltage, and prints the result to the serial monitor.
   Attach the center pin of a potentiometer to pin A0, and the outside pins to +5V and ground.
- 
+
  This example code is in the public domain.
  */