Updating examples.

build/shared/dist/examples/Digital/Blink/Blink.pde

@@ -0,0 +1,25 @@
+/*
+ * Blink
+ *
+ * The basic Arduino example.  Turns on an LED on for one second,
+ * then off for one second, and so on...  We use pin 13 because,
+ * depending on your Arduino board, it has either a built-in LED
+ * or a built-in resistor so that you need only an LED.
+ *
+ * http://www.arduino.cc/en/Tutorial/Blink
+ */
+
+int ledPin = 13;                // LED connected to digital pin 13
+
+void setup()                    // run once, when the sketch starts
+{
+  pinMode(ledPin, OUTPUT);      // sets the digital pin as output
+}
+
+void loop()                     // run over and over again
+{
+  digitalWrite(ledPin, HIGH);   // sets the LED on
+  delay(1000);                  // waits for a second
+  digitalWrite(ledPin, LOW);    // sets the LED off
+  delay(1000);                  // waits for a second
+}

build/shared/dist/examples/Digital/Button/Button.pde

@@ -0,0 +1,27 @@
+/*
+ * Button
+ * by DojoDave <http://www.0j0.org>
+ *
+ * Turns on and off a light emitting diode(LED) connected to digital  
+ * pin 13, when pressing a pushbutton attached to pin 7. 
+ *
+ * http://www.arduino.cc/en/Tutorial/Button
+ */
+ 
+int ledPin = 13;                // choose the pin for the LED
+int inputPin = 2;               // choose the input pin (for a pushbutton)
+int val = 0;                    // variable for reading the pin status
+
+void setup() {
+  pinMode(ledPin, OUTPUT);      // declare LED as output
+  pinMode(inputPin, INPUT);     // declare pushbutton as input
+}
+
+void loop(){
+  val = digitalRead(inputPin);  // read input value
+  if (val == HIGH) {            // check if the input is HIGH
+    digitalWrite(ledPin, LOW);  // turn LED OFF
+  } else {
+    digitalWrite(ledPin, HIGH); // turn LED ON
+  }
+}

build/shared/dist/examples/Digital/Loop/Loop.pde

@@ -0,0 +1,37 @@
+/*
+ * Loop
+ * by David A. Mellis
+ *
+ * Lights multiple LEDs in sequence, then in reverse.  Demonstrates
+ * the use of a for() loop and arrays.
+ *
+ * http://www.arduino.cc/en/Tutorial/Loop
+ */
+
+int timer = 100;                   // The higher the number, the slower the timing.
+int pins[] = { 2, 3, 4, 5, 6, 7 }; // an array of pin numbers
+int num_pins = 6;                  // the number of pins (i.e. the length of the array)
+
+void setup()
+{
+  int i;
+
+  for (i = 0; i < num_pins; i++)   // the array elements are numbered from 0 to num_pins - 1
+    pinMode(pins[i], OUTPUT);      // set each pin as an output
+}
+
+void loop()
+{
+  int i;
+  
+  for (i = 0; i < num_pins; i++) { // loop through each pin...
+    digitalWrite(pins[i], HIGH);   // turning it on,
+    delay(timer);                  // pausing,
+    digitalWrite(pins[i], LOW);    // and turning it off.
+  }
+  for (i = num_pins - 1; i >= 0; i--) { 
+    digitalWrite(i, HIGH);
+    delay(timer);
+    digitalWrite(i, LOW);
+  }
+}