Initial Arduino IDE based on Processing.

build/shared/lib/avrlib/conf/ks0108conf.h

@@ -0,0 +1,85 @@
+/*! \file ks0108conf.h \brief Graphic LCD driver configuration. */
+//*****************************************************************************
+//
+// File Name	: 'ks0108conf.h'
+// Title		: Graphic LCD driver for HD61202/KS0108 displays
+// Author		: Pascal Stang - Copyright (C) 2001-2003
+// Date			: 10/19/2001
+// Revised		: 5/1/2003
+// Version		: 0.5
+// Target MCU	: Atmel AVR
+// Editor Tabs	: 4
+//
+// NOTE: This code is currently below version 1.0, and therefore is considered
+// to be lacking in some functionality or documentation, or may not be fully
+// tested.  Nonetheless, you can expect most functions to work.
+//
+// This code is distributed under the GNU Public License
+//		which can be found at http://www.gnu.org/licenses/gpl.txt
+//
+//*****************************************************************************
+
+
+#ifndef KS0108CONF_H
+#define KS0108CONF_H
+
+// define LCD hardware interface
+// -LCD_MEMORY_INTERFACE assumes that the registers of the LCD have been mapped
+// into the external memory space of the AVR processor memory bus
+// -LCD_PORT_INTERFACE is a direct-connection interface from port pins to LCD
+// SELECT (UNCOMMENT) ONLY ONE!
+
+// *** NOTE: memory interface is not yet fully supported, but it might work
+
+//#define GLCD_MEMORY_INTERFACE
+#define GLCD_PORT_INTERFACE
+
+// GLCD_PORT_INTERFACE specifics
+#ifdef GLCD_PORT_INTERFACE
+	// make sure these parameters are not already defined elsewhere
+	#ifndef GLCD_CTRL_PORT
+		#define GLCD_CTRL_PORT	PORTB	// PORT for LCD control signals
+		#define GLCD_CTRL_DDR	DDRB	// DDR register of LCD_CTRL_PORT
+		#define GLCD_CTRL_RS	PB0		// pin for LCD Register Select
+		#define GLCD_CTRL_RW	PB1		// pin for LCD Read/Write
+		#define GLCD_CTRL_E		PB2		// pin for LCD Enable
+		#define GLCD_CTRL_CS0	PB3		// pin for LCD Controller 0 Chip Select
+		#define GLCD_CTRL_CS1	PB4		// pin for LCD Controller 1 Chip Select(*)
+		#define GLCD_CTRL_CS2	PB6		// pin for LCD Controller 2 Chip Select(*)
+		#define GLCD_CTRL_CS3	PB7		// pin for LCD Controller 3 Chip Select(*)
+		#define GLCD_CTRL_RESET	PB5		// pin for LCD Reset
+		// (*) NOTE: additonal controller chip selects are optional and 
+		// will be automatically used per each step in 64 pixels of display size
+		// Example: Display with 128 hozizontal pixels uses 2 controllers
+	#endif
+	#ifndef GLCD_DATA_PORT
+		#define GLCD_DATA_PORT	PORTC	// PORT for LCD data signals
+		#define GLCD_DATA_DDR	DDRC	// DDR register of LCD_DATA_PORT
+		#define GLCD_DATA_PIN	PINC	// PIN register of LCD_DATA_PORT
+	#endif
+#endif
+
+// GLCD_MEMORY_INTERFACE specifics
+#ifdef GLCD_MEMORY_INTERFACE
+	// make sure these parameters are not already defined elsewhere
+	#ifndef GLCD_CONTROLLER0_CTRL_ADDR
+		// absolute address of LCD Controller #0 CTRL and DATA registers
+		#define GLCD_CONTROLLER0_CTRL_ADDR	0x1000
+		#define GLCD_CONTROLLER0_DATA_ADDR	0x1001
+		// offset of other controllers with respect to controller0
+		#define GLCD_CONTROLLER_ADDR_OFFSET	0x0002
+	#endif
+#endif
+
+
+// LCD geometry defines (change these definitions to adapt code/settings)
+#define GLCD_XPIXELS			128		// pixel width of entire display
+#define GLCD_YPIXELS			64		// pixel height of entire display
+#define GLCD_CONTROLLER_XPIXELS	64		// pixel width of one display controller
+
+// Set text size of display
+// These definitions are not currently used and will probably move to glcd.h
+#define GLCD_TEXT_LINES           8     // visible lines
+#define GLCD_TEXT_LINE_LENGTH    22     // internal line length
+
+#endif